ZTW 1:8 BEAST 150A ESC.
High current applications finely tuned and tested by the experience technician. Proven to be top class, reliable and quality made. Featuring enhanced throttle response, brake and throttle linearity. Advance software interface to set up or update software to make adjustment on your PC. Making detail adjustments .You can make adjustments using programming card. Featuring Low voltage cut off, overheating protection, throttle signal loss protection. MOSFET design provide high current output {1080 amp peaks} lowest resistance {.0003 Ohm} Micro-fin aluminum heat sink and water proof. ZTW are compatible with Novak, LRP, Orion Sensorless brushless motor.
Technical Specification:
Model type : 1:8 Beast SS150
Length: 55mm
Width: 48mm
Height: 37mm
Weight: 149g
Max continuous Current: 150A
Burst current: 1080A
BEC output: 6V/8.4A
Motor type : 4 pole Sensorless and sensored brushless motor
Battery: 5-18 cell Nixx { NiMH/NiCd} or 2-6S Lipo
Resistance: 0.0002ohm
Suitable Vehicles: 1:8 on road or off cars and trucks, SCT.
Operate Environment: Waterproof design allow you to use in nearly for any environment.
POWERING UP THE ESC FOR THE FIRST TIME AND SETTING THE AUTOMATIC THROTTLE CALIBRATION
The ZTW ESC features Automatic Throttle Calibration to attain the smoothest throttle response and resolution throughout the entire throttle range of your transmitter. This step is done once to allow the ESC to “learn and memorize” your Transmitter’s throttle output signals and only repeated if you change your transmitter.
1. Switch your Transmitter ON and set the throttle stick to its maximum position.
2. Connect the battery pack , receiver and motor to the ESC. Wait for about 2 seconds, the motor will beep for twice, then put the throttle in the minimum position, the motor will also beep, which indicates that your ESC has got the signal range of the throttle from your transmitter. The throttle calibration is set and your ESC is ready to use.
ENTERING THE PROGRAMMING MODE
1. Switch your Transmitter ON and set the throttle to its maximum position.
2. Connect the battery pack to the ESC.
3. Wait until you hear two short beeps (?? ?? ?? ??) confirming that the ESC has now entered the programming mode.2
4. If the throttle stick is left in the maximum position beyond 5 seconds, the ESC will begin the sequence from one function and its associated setting options to another. (Please refer to the table below to cross reference the functions with the audible tones).
5. When the desired tone for the function and setting option is reached, move the throttle stick down to its minimum position. ESC will emit two beeps (**) confirming the new setting has been stored.
6. The ESC only allows the setting of one function at a time. Therefore should you require making changes to other function, disconnect the battery pack and wait 5 seconds to reconnect the battery and repeat the above step
Package total weight: 215.00 grams (incl. packaging)
ZTW 1:8 BEAST 150A ESC.
High current applications finely tuned and tested by the experience technician. Proven to be top class, reliable and quality made. Featuring enhanced throttle response, brake and throttle linearity. Advance software interface to set up or update software to make adjustment on your PC. Making detail adjustments .You can make adjustments using programming card. Featuring Low voltage cut off, overheating protection, throttle signal loss protection. MOSFET design provide high current output {1080 amp peaks} lowest resistance {.0003 Ohm} Micro-fin aluminum heat sink and water proof. ZTW are compatible with Novak, LRP, Orion Sensorless brushless motor.
Technical Specification:
Model type : 1:8 Beast SS150
Length: 55mm
Width: 48mm
Height: 37mm
Weight: 149g
Max continuous Current: 150A
Burst current: 1080A
BEC output: 6V/8.4A
Motor type : 4 pole Sensorless and sensored brushless motor
Battery: 5-18 cell Nixx { NiMH/NiCd} or 2-6S Lipo
Resistance: 0.0002ohm
Suitable Vehicles: 1:8 on road or off cars and trucks, SCT.
Operate Environment: Waterproof design allow you to use in nearly for any environment.
POWERING UP THE ESC FOR THE FIRST TIME AND SETTING THE AUTOMATIC THROTTLE CALIBRATION
The ZTW ESC features Automatic Throttle Calibration to attain the smoothest throttle response and resolution throughout the entire throttle range of your transmitter. This step is done once to allow the ESC to “learn and memorize” your Transmitter’s throttle output signals and only repeated if you change your transmitter.
1. Switch your Transmitter ON and set the throttle stick to its maximum position.
2. Connect the battery pack , receiver and motor to the ESC. Wait for about 2 seconds, the motor will beep for twice, then put the throttle in the minimum position, the motor will also beep, which indicates that your ESC has got the signal range of the throttle from your transmitter. The throttle calibration is set and your ESC is ready to use.
ENTERING THE PROGRAMMING MODE
1. Switch your Transmitter ON and set the throttle to its maximum position.
2. Connect the battery pack to the ESC.
3. Wait until you hear two short beeps (?? ?? ?? ??) confirming that the ESC has now entered the programming mode.2
4. If the throttle stick is left in the maximum position beyond 5 seconds, the ESC will begin the sequence from one function and its associated setting options to another. (Please refer to the table below to cross reference the functions with the audible tones).
5. When the desired tone for the function and setting option is reached, move the throttle stick down to its minimum position. ESC will emit two beeps (**) confirming the new setting has been stored.
6. The ESC only allows the setting of one function at a time. Therefore should you require making changes to other function, disconnect the battery pack and wait 5 seconds to reconnect the battery and repeat the above step
Choose ZTW, Choose Quality & Trust! ZTW Model was established in 2007, committing themselves to electronic power system for RC models. As an integrated enterprise with the ability to research & develop, produce and sell, their products have been selling well all over the 60 countries and districts in the world, which makes ZTW the most competitive brand and OEM enterprise through global RC lines. Its brushless ESC for car, boat, and helicopter & airplane are comparable to world famous brands especially in terms of performance in compatibility, reliability and stability.
To select ZTW is to select quality & trust. All products available at the largest online RC store.
Choose ZTW, Choose Quality & Trust! ZTW Model was established in 2007, committing themselves to electronic power system for RC models. As an integrated enterprise with the ability to research & develop, produce and sell, their products have been selling well all over the 60 countries and districts in the world, which makes ZTW the most competitive brand and OEM enterprise through global RC lines. Its brushless ESC for car, boat, and helicopter & airplane are comparable to world famous brands especially in terms of performance in compatibility, reliability and stability.
To select ZTW is to select quality & trust. All products available at the largest online RC store.
ATees.com uses cookies and similar technologies. By using ATees.com, you are agreeing to our revised Privacy Policy and Terms and Conditions, including our Cookie Policy.